Wednesday, May 23, 2012

Colette Iris Shorts


P5179971P5179970
Gosh, I have been so busy with sewing and other things that I haven't found the time to make a blog post. 

Since my last post I have made two garments, with another half finished. One of the things I completed was a pair of Iris shorts from Colette Patterns, which I made in navy drill, with Liberty lawn pockets, polka dot facings and Liberty faced hems.
P5189997
Colette patterns are drafted with a pear-shaped figure in mind and, having found the Beignet skirt pattern so wide on my hips, I wasn't sure whether I should bother even trying to make up my first proper pair of shorts/trousers from a pattern I knew would need a lot of alterations to make fit.

I was still on the fence when I had an "aha" moment. I was doing the Susan Khalje Craftsy course, The Couture Dress, and she has you make up a muslin first, but using the stitching lines as your point of reference instead of the cutting lines most of us are used to, and working with a generous seam allowance. I thought I would fit my muslin and then take it apart and use the muslin itself as the pattern pieces, just as she does.

I roughly cut out my paper pattern pieces. Then I decided which size was my starting point. Because it was trousers I went with the hip measurement, which was a size 2 (in this case, a bad move). Have I mentioned that I am NOT pear-shaped? There are only six inches difference between my waist and hip, and I think Colette Patterns have a ten inch difference. With Sewaholic it's a twelve-inch difference. You can imagine how HUGE everything is on my hips (or how small on the waist!) Anyhow, since I chose my size for the shorts by hip measurement it meant I would have to hugely alter the waist size on this muslin. However, it wasn't as simple as that, as it turned out everything was wrong for me, including the crotch depth. But it was surpisingly "possible" to get them to fit in the end because of the way I did it. But I haven't explained yet.

 As I said, I roughly cut out my pattern pieces. I marked the stitching lines for the size I chose, 1.5cm in from
what would usually be the cutting line.
P5049738
I pinned the pattern pieces to the muslin fabric and traced the stitching lines, notches etc. onto the muslin.  Then I stitched along the stitching lines to make a permanent reference that wouldn't rub off, and it would stop the fabric stretching out, too.
P5049739
P5049741
I then stitched the pieces together along the stitching lines and when I tried on the shorts I realised that the whole fit was so wrong on me.  I mean, everything.  I won't go into details because it would bore the pants off you, but I took the muslin apart, remarked the stitching lines as a size 6 (nearer my waist size) and took in the hips a bit here and there, and tweaked various other bits, like the crotch depth etc.  What I ended up with was  totally personalised pattern which was nowhere near any of the standard sizes.  But instead of having to somehow transfer that to my paper pattern, which would have been too complicated for me to bother, all I had to do was take my muslin apart (having marked all the revised stitching lines carefully) and use it to cut out my main fabric. You can see my revised stitching lines marked in green (click the photos for larger sizes).
P5059743
It worked really well and I am so happy with the result.  I am planning to make the Iris shorts again in red drill, and all I will have to do is use my muslin pieces, which are all nicely folded inside my pattern wallet.  How cool is that?  I really don't think I could have fitted these shorts if I had just cut out one size, with a 1.5 seam allowance, instead of about a 3cm allowance, in the usual way.  I would have ended up binning the whole attempt.  I tried the Clover trousers a few months ago and just couldn't get them to fit, having cut out a size 4.  Again, it was all wrong.  Next time I will cut a size 6 with huge seam allowances and tweak and tweak until they are right, and then use my muslin as the pattern again.  I think I can do it.  It's a time consuming process, though not too bad for a pair of shorts, and I will only use it for items that require a lot of fitting.


Wednesday, May 09, 2012

McCalls M5661 Version D

P5039722
P5039721
The first one of these I made up in a soft, textured silk. It was easy and quick to make up and I really enjoy wearing it, so I thought I would make another.

What fabric to make it up in...? I had some silk, which was "hand printed in England", so I thought I'd stick with the silk theme and use that. It would be simple: I had made the exact top before, and in silk.

This time it was an absolute pain.

For a start, the pleats along the top were difficult to get in place because the silk would not crease at all. It was kind of springily resistant. Which is odd, considering how dreadfully it had creased during the washing process. Once the pleats were in place, I pinned the neck facing on, only to find that it was much smaller than the neckline of the pleated bit. I wasn't sure whether the application of the interfacing to the facing had shrunk the silk, or what.
P5039726
My interfacing was odd, anyway. It had seemed like a nice, flexible light weight, but once ironed on the whole facing became sort of crisp. Which leads me to the next problem: despite trimming the seams, making notches, you name it, the facing and the outer shell did not sit nicely together and seemed to pull against each other. For goodness sake. It's not bad enough to stop me wearing the top, but it pulls in places it shouldn't. 

In exasperation I checked the facings on my black silk version, only to find I hadn't bothered interfacing them at all, which meant the facings were all lovely and fluid, just like the main top. Goodness know why I didn't bother with the interfacing on the first version. I think I just forgot! It's taught me a lesson though: sometimes you don't need interfacing even though the pattern says you do. My black silk top has been washed and ironed many times, and has not suffered for having no interfacing.
P5039732
After finally sewing the top together, the buttons and buttonholes went smoothly. The top is very...um...pretty. It actually looks okay with jeans, but unless dressed down, it looks a bit bridesmaid-y. I will make another one of these tops, but a different version, and I'll be careful about the fabric I choose, and about the interfacing I use.